PAM Emulsion 1630

RXSOL PAM Emulsion 1630

Product Code: RXSOL-34-4160-025

Product Description

RXSOL PAM Emulsion 1630 is a high-performance polyacrylamide (PAM) emulsion formulated for efficient solid-liquid separation in water and wastewater treatment applications. The active polyacrylamide polymer is dispersed in an oil phase using inverse-emulsion technology, providing a convenient liquid polymer with rapid activation in water.

RXSOL PAM Emulsion 1630 functions as an effective flocculant, promoting the aggregation of fine suspended and colloidal particles into larger, stronger flocs. This improves settling, clarification, flotation and sludge dewatering performance in a wide range of industrial processes.

Unlike conventional dry polyacrylamide powders that require extended preparation and maturation time, RXSOL PAM Emulsion 1630 inverts and dissolves rapidly when properly dispersed in water, typically developing within approximately 5–15 minutes, depending on water quality, temperature, concentration and mixing conditions.

Anionic Polyacrylamide Flocculant

Anionic Polyacrylamide Flocculant is an medium anionic charged polyelectrolyte to be used as flocculant in direct filtration process for settling of inorganic suspended solids, effluent water.

Properties : 

Applications

RXSOL PAM Emulsion 1630 is suitable for a wide range of solid-liquid separation processes, including:

• Municipal sewage and wastewater treatment
• Industrial effluent treatment
• Sludge thickening and dewatering
• Clarification and sedimentation
• Dissolved Air Flotation (DAF) systems
• Paper and pulp processing
• Textile and dyeing wastewater treatment
• Coal washing and mineral processing
• Mill and process wastewater treatment
• Oilfield and drilling-water treatment
• Produced-water treatment
• Mining and mineral-processing applications
•  

It is used for effluent treatment of inorganic suspended solids found in chemical, Fishery, food, textile, dye, other effluent water, mining and coal washing waste water, metal processing, etc.

Dosage

The dosage range of Anionic Polyacrylamide Flocculant  Anionic Polyelectrolyte Powder varies from 0.2 - 3.0 ppm depending upon the type of effluent and application. It is always advised to do a jar test for evaluating the functioning and approximate dosage of Anionic Polyacrylamide Flocculant  Anionic Polyelectrolyte Powder.

Jar Test: Put sample of effluent in a beaker and add Anionic Polyacrylamide Flocculant Powder as designated, agitate for 1 minute at 100-120 rpm and then slowly agitate at 60rpm. Determine the floc properly at this time and note the sedimentation and clarity of top solution.

Procedure and precautions upon dispersion and dissolving flocculants:-

Dissolving time: The time required to dissolve the flocculant varies according to the type of flocculant, water quality, temperature and agitation. However, most flocculants generally require around 1 hour of agitation to completely dissolve the powder. Incomplete mixture of flocculant or lumping may inhibit the performance of the flocculant.

Agitation speed: The ideal revolution of the agitator is between 200-400rpm. A high speed agitator operating without reducing the revolution of a motor is not advised, since it may cut the molecules of the flocculant. An ideal agitator motor should be of 1HP for a 1-2m3 mixing tank.

Dissolving concentration: Flocculants should be standardly be dissolved to 0.1-0.2% concentration. It is also effective to start dissolving at a slightly higher concentration, and then dilute the flocculant mixture immediately before use.

Notes

Uses

RXSOL PAM Emulsion 1630 is used where rapid and efficient flocculation of suspended solids is required. It helps improve floc formation, settling rate, water clarity, sludge concentration and dewatering efficiency, while potentially reducing the overall volume of sludge requiring handling and disposal.

The product is particularly suitable for applications requiring a liquid polymer that can be prepared more rapidly than conventional dry PAM products and integrated into continuous chemical dosing systems.

Handling measures and precautions : 

Proper human safety products such as Splash goggles, lab coat, vapor respirator, gloves and boots should be worn while handling and applying chemicals. Splashes on skin should be washed off with water immediately. In case of splashing into the eyes, flush it with fresh water and obtain medical attention. Should not be injected. Please refer MSDS for more details.

Storage: 
 
This product should be stored in original containers in cool and dry place, away from sources of heat, flame and direct sunlight.

Supply location

Anionic Polyacrylamide Flocculant Powder manufacturer supplier exporter in Fujairah, Dubai, Sharjah, Ajman, Abudhabi, Gulf, Yemen,UAE Middle East, Ruwi, Ghala, Muscat Barka Oman, Nairobi Kenya Africa, Mumbai, Kandla, Kolkata, Vishakhapatnam, Chennai, India, Canada, Nairobi Kenya, Sudan

Generic name

Keywords

Anionic Polyacrylamide Flocculant Powder manufacturer supplier exporter in Mumbai, Kandla, Mundra, Kolkata, Howrah, Vishakhapatnam, Chennai, India.
Anionic Polyacrylamide Flocculant Powder manufacturer supplier exporter in Fujairah, Dubai, Abu Dhabi, Sharjah, Ajman, UAE Middle East.
Anionic Polyacrylamide Flocculant Powder manufacturer supplier exporter in Muscat Barka Oman.
Anionic Polyacrylamide Flocculant Powder manufacturer supplier exporter in Nairobi Mombasa Kenya Africa, Canada.