RXSOL ORG-20 ABS (RXSOL-19-7008-050) is listed by the manufacturer as a cement remover. Here are six jobs this type of product typically does in Oman plants and workshops, and the checks to run before you use it.
TL;DR
- RXSOL ORG-20 ABS, part number RXSOL-19-7008-050, is listed by the manufacturer as a cement remover.
- Typical jobs for this product class: site tools, mixer drums, concrete pumps, ready-mix equipment, formwork, and mortar stains on brick and tile.
- Dilution and contact time vary by formulation; get the figures for RXSOL-19-7008-050 from the SDS and technical bulletin.
- Test a small area first. Cement removers differ in how they treat stainless steel, aluminium, paint, seals and plastics.
- Collect rinse water and residue for classification and arrange disposal through be'ah and the Environment Authority.
RXSOL ORG-20 ABS (part number RXSOL-19-7008-050) is listed by the manufacturer as a cement remover. Cement removers of this type are used to remove hardened cement, concrete and mortar residue.
Below are six jobs that cement removers of this type usually do, followed by the checks your plant or workshop in Muscat should run before the product goes on site. For the exact dilution, contact time and compatible materials, use the technical details, technical bulletin and SDS for this part number, available on request.
What is RXSOL ORG-20 ABS used for?
The manufacturer lists RXSOL ORG-20 ABS as a cement remover, and makes its technical details, dosage guidance and safety data sheet available on request. The table shows what we can confirm and what you should take from those documents.
| Item | Detail |
|---|---|
| Part number | RXSOL-19-7008-050 |
| Product type | Cement remover (manufacturer listing) |
| Typical applications for this product class | Hardened cement and concrete on tools, mixers, ready-mix trucks, concrete pumps and formwork; cement and mortar stains on brick and tile |
| Dilution and contact time | Depends on the formulation: see the technical bulletin and SDS, available on request (typical figures for this product class are given below) |
| Application temperature | See the technical bulletin; one cement remover of this class is rated for 5-30 °C air and surface temperature |
| SDS and technical details | Available on request, quoting the part number |
6 typical uses of a cement remover like RXSOL ORG-20 ABS
Each use below is a standard job for cement removers of this type. Before you start, ask us to confirm that RXSOL ORG-20 ABS suits your equipment material.
1. Hand tools and site tools
Cement that sets on trowels, floats, shovels, wheelbarrows and vibrator pokers costs hours of chipping. Cement removers are used to remove hardened cement and concrete from tools. On thick layers, chip off the bulk first so the liquid can reach the thin layer bonded to the tool.
2. Concrete mixer drums and ready-mix trucks
Build-up inside a mixer drum adds dead weight and cuts the volume the drum can carry. This product class is used on concrete mixers and ready-mix trucks. Ask us to confirm suitability for your drum steel and any painted outer surfaces before you treat a whole fleet.
3. Concrete pumps and delivery lines
Cement slurry left in a pump hopper, valve or boom line hardens and restricts flow at the next pour. Cement removers are used to clean concrete pumps in the ready-mix industry. Protect rubber seals, hoses and gaskets near the treated area until compatibility is confirmed.
4. Batching plant and other ready-mix equipment
Concrete batching plants in Muscat, Sohar and Duqm collect cement residue on hoppers, skips and discharge chutes. Cement removers are used on concrete pumps and other ready-mix equipment; batching plant hoppers and chutes collect the same residue, so confirm suitability with us first. Plan the clean for a shutdown, and keep the liquid away from electrical panels and load cells.
5. Formwork and shutters
Cement and mortar left on formwork spoil the finish of the next pour and shorten panel life. Cement removers are used to strip these deposits from formwork. Test one panel first, because steel, plywood and plastic forms each react differently.
6. Mortar stains on brickwork and tiles
Mortar smears and cement haze on new brickwork or tiling are common snag-list items at handover. This product class is used to remove cement and mortar stains from brick and tiled surfaces. Grout and mortar joints are cement-based too, so test a small area to check that the remover does not attack the joint along with the stain.
Compatibility checks and a small-area trial
Compatibility depends on the formulation, so take it from the technical bulletin for this part number and your own trial, never from another product's datasheet. Some cement removers must not be used on stainless steel or aluminium while others are rated safe on steel and stainless steel. Some can also damage nearby paint, metals and plastics.
| Use | Base material to check | Nearby parts to protect |
|---|---|---|
| Site tools | Steel, aluminium | Timber handles, painted parts |
| Mixer drums | Drum steel | Outer paintwork |
| Concrete pumps | Steel hopper and lines | Seals, hoses, gaskets |
| Batching plant | Steel hoppers and chutes | Electrical panels, load cells, painted frames |
| Formwork | Steel, plywood, plastic | Coated panel faces |
| Brick and tile | Brick, tile, grout | Joints, metal frames, glass |
Run this trial before the first full application:
- Request the current SDS and technical bulletin for RXSOL-19-7008-050 and read the PPE, dilution and rinse sections.
- Choose a small, out-of-sight area that has the same deposit and base material as the full job.
- Apply the product as the technical bulletin directs, leave it for the stated contact time, then clean the area as directed.
- Let the area dry, then check for etching, discolouration, softened seals or loose grout.
- Record the dilution, contact time, surface temperature and result. Treat the full area only after that.
Dilution, contact time and Oman heat
Dilution and contact time depend on the formulation. The figures below are typical for this type of product, taken from other manufacturers' datasheets; the technical bulletin for RXSOL ORG-20 ABS, available on request, gives the figures for this part number.
- One acid-based cement remover has a typical working dilution of 5-10%, given as 50-100 mL of product per litre of water, with at least 10 minutes of contact before rinsing.
- Another cement remover comes ready to use and needs 10-15 minutes of initial penetration.
- One ready-to-use product uses approximately 150 g/m², depending on how thick the deposit is.
One manufacturer rates its cement remover for 5-30 °C air and surface temperature. In Muscat or Duqm, steel drums, chutes and formwork left in the sun can get much hotter than that for much of the year. Plan the clean for early morning or a shaded area, and let the surface cool first.
A cement remover technical sheet calls for protective gloves, glasses and suitable clothing. Your exact PPE and ventilation come from the product SDS and your own risk assessment. Choose gloves rated for this formulation, because a mixture can pass through glove materials differently from its individual ingredients.
Collecting rinse water and residue in Oman
Treat used cleaning liquid, rinse water and removed residue as waste to be classified. Do not assume they are safe to send to a drain. Collect them in a drip tray or contained wash area while the clean is in progress.
Oman's Environment Authority requires a waste management licence for any business that collects, transports, stores, treats, reuses or disposes of hazardous waste. For industrial waste it accepts, be'ah requires hazardous waste to be packed in UN-approved containers unless it approves an alternative, with the correct label and manifest number on the packaging. In Sohar Port and Freezone, waste generators submit waste details to be'ah, use its manifest system and arrange an approved transporter.
Where to buy RXSOL ORG-20 ABS in Muscat and Oman
Muscat Chemical (Muscat & Barka for Business Trading) supplies RXSOL ORG-20 ABS from Barka Industrial Area, Sultanate of Oman. The RXSOL ORG-20 ABS product page carries the part number. If you need other site chemicals on the same delivery, see our full chemical range.
We deliver from our Barka warehouse to plants, batching sites and workshops in Muscat, Ruwi and across Oman. For jobs on the Batinah coast, our Sohar site lists the same part number for Sohar port and industrial area deliveries. Oman Chemical's RXSOL ORG-20 ABS page takes MSDS and technical bulletin requests for other regions.
To request a quote for RXSOL ORG-20 ABS, call +968 77333599, message us on WhatsApp at +968 77333599, email muscatchem@gmail.com or use our quote request form. Give us the part number, the equipment material, the type of deposit and the quantity you need, and ask for the SDS and technical details, which are available on request.
Need RXSOL ORG - 20 ABS? Ask us for a quote, the TDS or the MSDS. Delivery across Oman from our Barka warehouse.
Frequently asked questions
What is RXSOL ORG-20 ABS used for?
RXSOL ORG-20 ABS, part number RXSOL-19-7008-050, is listed by the manufacturer as a cement remover. Products of this type are used on hardened cement and concrete on tools, mixer drums, ready-mix trucks, concrete pumps and formwork, and on mortar stains on brick and tile. Confirm your exact use against the technical details, available on request.
Does RXSOL ORG-20 ABS need dilution, and how long should it stay in contact?
It depends on the formulation. One acid-based cement remover from another manufacturer is used at 50-100 mL per litre of water with at least 10 minutes of contact, while another is ready to use with 10-15 minutes of penetration. Take the figures for RXSOL ORG-20 ABS from its technical bulletin and SDS, available on request.
Which metals, coatings and seals are compatible with RXSOL ORG-20 ABS?
Compatibility differs between cement removers. Some must not be used on stainless steel or aluminium, and some can damage paint and plastics. Check the technical details for this part number and run a small-area trial on your actual material before full use.
How should cement residue and cleaning liquid be disposed of in Oman?
Collect used liquid, rinse water and residue for classification instead of sending them to a drain. be'ah requires hazardous waste in UN-approved containers with the correct label and manifest number, and businesses handling hazardous waste need an Environment Authority licence.
How can a plant get the current SDS and technical data?
Call +968 77333599, message us on WhatsApp or email muscatchem@gmail.com, quoting part number RXSOL-19-7008-050. The technical details, dosage guidance and SDS are available on request, so ask for them with your quote.